My project

All Posts

1 2 3 4 5
>
Forum Index -:- Projects and Builds

#1: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Thu Mar 03, 2011 05:45 PM
    ----
This is what I have started on. 69 that is in good shape only rust is in the rear storage area behind rear seat. Have done some cutting and trimming.
Here is what I have done so far.






Last edited by PaDan on Sun Mar 06, 2011 03:10 AM; edited 3 time in total

#2: My project Author: bugzapper , Location: minnesota Post Posted: Fri Mar 04, 2011 02:21 AM
    ----
pics arent working

#3: Re: My project Author: perrib , Location: Chandler Post Posted: Fri Mar 04, 2011 06:16 AM
    ----
bugzapper wrote:
pics arent working

X2

Are you using photo bucket. If so copy and paste the IMG code into your post.

#4: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Sun Mar 06, 2011 03:11 AM
    ----
I got the pic's working

#5: Re: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Fri May 27, 2011 06:41 PM
    ----
Not much progress. Pulled the type 1 trans out ready to put the 002 bus trans in. Put the body back on the pan. Now just waiting on a punch of parts that I have on order.




#6: My project Author: crestfallen , Location: Wheeling, WV Post Posted: Fri May 27, 2011 11:23 PM
    ----
Like the purple, and good progress!

#7: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Mon Jul 25, 2011 10:28 PM
    ----
Well, been a little bummed since the ass----- toke my money for the one piece front end and run Crying or Very sad . I hope someone runs over that bas---. Okay thats water under the bridge now and sorry for the words. Here is what I have gotten done even with the set back.
[img][/img]
cut and plated frame horns

[img][/img]
[img][/img]
002 installed and ready for adapter plate
[img][/img]
main cage parts installed
[img][/img]
master cylinder installed no lines installed yet need to pull body off again for paint
[img][/img]
installed lower stiffeners for check on fit

#8: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Wed Nov 02, 2011 02:05 AM
    ----
I have more progress to show everyone

[/img]
front end tacked together



trimmed fiberglass to fit and getting fuel tank in location

#9: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Wed Jan 04, 2012 05:37 AM
    ----
Painted all the front end tubing and roll cage got a nice delivery today the KEP engine adapter made it. I now need to go pickup the motor.

#10: My project Author: AzBaja , Location: Mesa, AZ Post Posted: Fri Jan 06, 2012 06:31 AM
    ----
You can still get the gas tank out of the car if you need to? Do not forget you need to get thing out of the car for repairs at some date.

I have seen a Baja with the engine and trans locked in place. Person did not think about ever needing to remove them.

#11: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Fri Jan 06, 2012 08:31 PM
    ----
I made every thing so that it can be removed and serviced or replaced as needed.

#12: Re: My project Author: POCman , Location: Mid Willamette Valley Oregon Post Posted: Sat Jan 07, 2012 09:03 AM
    ----
NICE!!!
Shes looking pretty stout. Good idea touching the shock towers if youre goin to be hittin it hard!!!
But the tank has me in question too????

#13: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Tue Jan 10, 2012 03:18 AM
    ----
Did some mockup. What do you think?



Found these led clearance lights I think they will make good turn indicators


#14: Re: My project Author: POCman , Location: Mid Willamette Valley Oregon Post Posted: Tue Jan 10, 2012 12:49 PM
    ----
Ya have two thumbs up from me.......NICE Work!!!

#15: My project Author: PaDan , Location: Twin Falls, Idaho Post Posted: Wed Jan 18, 2012 05:37 AM
    ----
Painted the rear fenders, sun visor, sun roof and the front end today.

Moved the body back in to get the final sanding done and I hope paint tomorrow. We are predicted to get 3 to 6 inches of snow tonight. Crying or Very sad



Forum Index -:- Projects and Builds

1 2 3 4 5
>
Page 1 of 5